Honda Tsivik
+ Cars of the mark of It Treats Full text and Honda Civic With care
+ Maintenance education
+ Regular maintenance
- Motor
+ Repair of the motor without extraction of the car - the Civic model
+ Repair of the motor without extraction of the car - the Full text model
+ General and repairs of capital of the motor
+ Cooling of system and heating
+ System of provision of power and launch
+ Electric motor equipment
+ Systems of control of the motor
+ Box of dislocation of gear
+ Union and ends of power
+ Brakes system
+ Support of the triangular form of interruption and direction
+ Body
+ Electric side equipment
|
Motor Specifications
I repair without extraction of the car – the Civic model
General parameters
| Characteristic |
Value |
Ignition order | 1-3-4-2 |
Cylinders numeration (in front behind) | 1-2-3-4 |
Diameter of cylinders, mm | 74.93 |
Blow of piston, mm | 89.92 |
Work volume, cm3 (l) | 1589 (1.6) |
Agreement of cylinders and direction of rotation of the distributor of ignition
Axle
| Characteristic |
Value |
Play of axial side, mm | |
Nominal | 0.051 |
Admissible limit | 0.152 |
Height of came in the rise airplane, mm | |
D16Y5 | |
Entry | |
Elementary education | 38.4277 |
Secondary | 32.1920 |
End | 38.7833 |
D16Y7 | |
Entry | 35.2984 |
End | 37.2821 |
D16Y8 | |
Entry | |
Pervichye | 36.7767 |
Intermediary | 38.2727 |
Secondary | 37.0637 |
End | 38.0086 |
Angry thrashing, mm | |
Nominal | 0.025 |
Admissible limit | 0.051 |
Work slit in loads, mm | |
Nominal | 0.0508÷0.1016 |
Admissible limit | 0.152 |
Oil bomb
| Characteristic |
Value |
Slits of work of wheels of gear, mm | |
Axial slit of wheels of gear | |
Nominal | 0.025÷0.076 |
Admissible limit | 0.152 |
Split between tops of teeths of gear wheels | |
Nominal | 0.025÷0.152 |
Admissible limit | 0.203 |
Split between a wheel of extern gear and walls of the case | |
Nominal | 0.102÷0.178 |
Admissible limit | 0.203 |
Efforts of corseting itself of screwed connections, Nanômetro
| Characteristic |
Value |
Pins of fixation of coverings of loads of the axle | |
Pins in 6 mm | 12.2 |
Pins in 8 mm | 19 |
Pin of cog-wheel of axle | 37 |
Pin of fixation of the sensor of fluctuations of an end of inclination | 11.8 |
Pin of a pulley of an end of inclination | 182 |
Pins of a head of cylinders | |
Stage 1 | 19 |
Stage 2 | 49 |
Stage 3 | 66 |
Stage 4 | 66 |
Pins of fixation of a disc of driving to an inclination end | 73 |
Nuts of fixation of the oil pipeline of entry | 23 |
Nuts of fixation of a final collector to a head of cylinders | 31 |
Nuts of fixation of a tube of reception to a final collector | |
D16Y5, D16Y7 | 34 |
D16Y8 | 54 |
Pins of the superior covering of a final collector | 23 |
Pins of fixation of the lowest covering of a final collector (D16Y5, D16Y7) | 10.8 |
Pins of fixation of a pendulum to an inclination end | 118 |
Sensor of oxygen (l-probe) | 45 |
Switch of sensor of pressure of oil | 17.6 |
Drain the cork of the trundle bed of a case of the motor | 39 |
Pins of fixation of the trundle bed of a case to the motor | 11.8 |
Nuts of fixation of a tube maslozaborny to a bomb accommodation | 10.8 |
Fixation of a maslozabornik of the bomb of oil to the bridge of coverings of radical loads | 10.8 |
Pins of fixation of the case of the bomb of oil to the motor | 10.8 |
Screws of fixation of a covering of the bomb of oil | 6.8 |
Pins of the bearer of a few back epiploon of an inclination end | 10.8 |
Pins of fixation of coverings of a belt that distributes the gas | 9.7 |
Pin of fixation of a natyazhitel of a belt that distributes the gas | 45 |
Pins of fixation of a covering of a head of cylinders | 9.7 |
Pins of fixation of the valve eletromagnética of blockade of VTEC | 11.8 |
Pins of fixation of the water bomb | 12.2 |
I repair without extraction of the car – the model of Full text
General parameters
| Characteristic |
Value |
Ignition order | 1-3-4-2 |
|
Cylinders numeration (of of the left on the right) | 1-2-3-4 |
Diameter of cylinders, mm | 81.03 |
Blow of piston, mm | |
B18B1
| 88.90 |
| B18C1 and B18C5 | 87.12 |
| Work volume, cm3 (l) | |
B18B1
| 1835 (1.8) |
| B18C1 and B18C5 | 1803 (1.8) |
Agreement of cylinders and direction of rotation of the distributor of ignition
Axle
| Characteristic |
Value |
Play of axial side, mm | |
Nominal | 0.051÷0.152 |
Admissible limit | 0.508 |
Height of came in the rise airplane, mm | |
B18B1 | |
Entry | 33.7160 |
End | 33.5280 |
B18C1 | |
Entry | |
Pervichye | 33.4112 |
Intermediary | 36.3779 |
Secondary | 34.5465 |
End | |
Pervichye | 33.1114 |
Intermediary | 35.7200 |
Secondary | 34.3814 |
B18C5 | |
Entry | |
Pervichye | 33.0886 |
Intermediary | 35.9105 |
Secondary | 34.7320 |
End | |
Pervichye | 32.7838 |
Intermediary | 36.3322 |
Secondary | 34.6913 |
Angry thrashing, mm | |
Nominal | 0.025 |
Admissible limit | 0.051 |
Work slit in loads, mm | |
| B18B1 | |
Nominal | 0.0305÷0.0686 |
Admissible limit | 0.152 |
| B18C1 and B18C5 | |
Nominal | 0.0508÷0.0889 |
Admissible limit | 0.152 |
Oil bomb
| Characteristic |
Value |
Slits of work of wheels of gear, mm | |
Axial slit of wheels of gear | |
Nominal | 0.025÷0.076 |
Admissible limit | 0.152 |
Split between tops of teeths of gear wheels | |
Nominal | 0.051÷0.152 |
Admissible limit | 0.203 |
Split between a wheel of extern gear and walls of the case | |
Nominal | 0.025÷0.076 |
Admissible limit | 0.152 |
Efforts of corseting itself of screwed connections, Nanômetro
| Characteristic |
Value |
Pins of fixation of coverings of loads of the axle | |
B18B1 | 12.2 |
B18C1 and B18C5 | |
Pins in 6 mm | 12.2 |
Pins in 8 mm | 27 |
Pins of cog-wheel of axle | |
B18B1 | 37 |
B18C1 and B18C5 | 56 |
Pins of the sensor of fluctuations of an end of inclination | 10.8 |
Pin of a pulley of an end of inclination | 176 |
Pins of a head of cylinders | |
Stage 1 | 30 |
Stage 2 | |
B18B1 | 83 |
B18C1 and B18C5 | 85 |
Pins of fixation of a disc of driving to an inclination end | 73 |
Pins / nuts of fixation of the oil pipeline of entry | 23 |
Nuts of fixation of an air camera of the oil pipeline of entry (B18C1) | 23 |
Nuts of fixation of a final collector to a head of cylinders | 31 |
Nuts of fixation of a tube of reception to a final collector | 54 |
Pins of the superior covering of a final collector | 23 |
Pins of fixation of a pendulum to an inclination end | 103 |
Sensor of oxygen (l-probe) | 45 |
Pins of a masloraspylitel | 17.6 |
Switch of sensor of pressure of oil | 17.6 |
Pins of fixation of a plate maslootrazhatelny of the trundle bed of a case | |
B18B1 and B18C1 | 10.8 |
B18C5 | 9.7 |
Drain the cork of the trundle bed of a case of the motor | 45 |
Pins of fixation of the trundle bed of a case to the motor | 10.8 |
Nuts of fixation of a tube maslozaborny to a bomb accommodation | |
B18B1 and B18C1 | 10.8 |
B18C5 | 9.7 |
Fixation of a maslozabornik of the bomb of oil to the bridge of coverings of radical loads | |
B18B1 and B18C1 | 10.8 |
B18C5 | 9.7 |
Pins of fixation of the case of the bomb of oil to the motor | |
6 mm pins | |
B18B1 and B18C1 | 10.8 |
B18C5 | 9.7 |
8 mm pins | 23 |
Fixation of a covering of the bomb of oil | |
1994 and 1995 | 5.4 |
from 1996 | 6.8 |
Cork of the valve that it reduces of the oil bomb | 39 |
Pins of the bearer of a few back epiploon of an inclination end | 10.8 |
Pins of fixation of coverings of a belt that distributes the gas | 9.7 |
Pin of fixation of a natyazhitel of a belt that distributes the gas | 5.4 |
Nuts of fixation of a covering of a head of cylinders | 9.7 |
Pins of fixation of the valve eletromagnética of blockade of VTEC | 11.8 |
Pins of fixation of the water bomb | 11.8 |
General and repairs of capital of the motor
Civic models
General parameters
| Characteristic |
Value |
Compression pressure in cylinders, kgf/cm2
| |
Nominal | 12.9 |
The admissible minimum | 9.5 |
The very admissible difference between cylinders | 2.0 |
The pressure of oil (the motor is heated up to the temperature of normal work), kgf/cm2
| |
In the only turns | 0.7 |
With a frequency of rotation of the motor of 3.000 revolutions per minute | 3.5 |
Block of motor
| Characteristic |
Value |
Diameter of cylinders, mm | |
Nominal | 75.0011÷75.0189 |
Admissible limit | 75.0697 |
conicity admissible extreme of the cylinder, mm | 0.051 |
ovality admissible extreme of the cylinder, mm | 0.051 |
Limit the admissible excess of the diameter of the cylinder, mm | 0.510 |
Admissible extreme not planeness of the inter-connected surface, mm | 0.102 |
Pistons and rings of piston
| Characteristic |
Value |
Diameter of pistons, mm | 74.9808÷74.9910 |
Nominal | 74.9706 |
Admissible limit | 5.16 |
Height of a point of measurement of diameter of a reduction of a skirt, mm | |
Slit of landing of the piston in the cylinder, mm | |
Nominal | 0.0102÷0.0406 |
Admissible limit | 0.051 |
The slit of the landing of the piston touches flutes, mm | |
Ring of superior compression | 0.0356÷0.0610 |
Nominal | 0.127 |
Admissible limit | |
According to compression ring | |
Nominal | 0.0305÷0.0559 |
Admissible limit | 0.127 |
Slits in locks of rings of piston, mm | |
Ring of superior compression | |
Nominal | 0.152÷0.305 |
Admissible limit | 0.610 |
According to compression ring | |
Nominal | 0.305÷0.457 |
Admissible limit | 0.711 |
Ring of scraper of oil | |
Nominal | 0.203÷0.711 |
Admissible limit | 0.787 |
End of inclination and sticks
| Characteristic |
Value |
Play of axial side, mm | |
Nominal | 0.102÷0.356 |
Admissible limit | 0.457 |
Necks of radical loads | |
Diameter, mm | 54.9758÷55.0012 |
conicity admissible extreme, mm | 0.0051 |
ovality admissible extreme, mm | 0.0051 |
Limit the admissible thrashing, mm | 0.051 |
Work slit in radical loads, mm | |
Necks 1 and 5 | |
Nominal | 0.0178÷0.0356 |
Admissible limit | 0.051 |
Necks 2, 3 and 4 | |
Nominal | 0.0229÷0.0432 |
Admissible limit | 0.051 |
Loads necks conrod | |
Diameter, mm | 44.9758÷45.0012 |
conicity admissible extreme, mm | 0.0051 |
ovality admissible extreme, mm | 0.0051 |
Limit the admissible thrashing, mm | 0.051 |
Work slit in loads conrod, mm | |
Nominal | 0.0203÷0.0381 |
Admissible limit | 0.051 |
Play of side of side of sticks, mm | |
Nominal | 0.152÷0.305 |
Admissible limit | 0.406 |
Head of cylinders and mechanism valvate
| Characteristic |
Value |
Admissible extreme not planeness of the inter-connected surface of a head, mm | |
Without in favor point | 0.051 |
Repair | 0.203 |
Height of a head of cylinders, mm | 92.939÷93.040 |
Angle of canvas of a facet of saddles valvate | 45 ° |
Angle of canvas of a facet of work of plates of valves | 45 ° |
Width of a cylindrical part (consolation) of the surface of plate that is formed of the valve, mm | |
Entry valves | 0.660 |
Final valves | 0.940 |
Diameter of a nucleus of the valve, mm | |
Entry valves | |
Nominal | 5.4788÷5.4889 |
Admissible limit | 5.08 |
Final valves | |
Nominal | 5.4508÷5.4610 |
Admissible limit | 5.04 |
Internal diameter of the captures of direction of valves, mm | |
Nominal | 5.512÷5.537 |
Admissible limit | 5.563 |
Slit of landing nucleus of valves in the direction captures, mm | |
Entry valves | |
Nominal | 0.025÷0.051 |
Admissible limit | 0.076 |
Final valves | |
Nominal | 0.051÷0.076 |
Admissible limit | 0.102 |
Adjusting height of nucleuses of valves, mm | |
Nominal | 53.162÷53.645 |
Admissible limit | 53.899 |
Free spring length valvate, mm | |
D16Y7 | 57.91 |
D16Y5 | |
Entry valves | 56.39 |
Final valves | 57.91 |
D16Y8 | |
Entry valves | 57.91 |
Final valves | 58.67 |
Efforts of corseting itself of screwed connections, Nanômetro
| Type of connection |
Value |
Pins of coverings of radical loads | |
Stage 1 | 24 |
Stage 2 | 52 |
Nuts of coverings of the lowest leaders of sticks | 31 |
* Also to see Specifications to Repair without extraction of the car – the Civic model.
Models of Full text
General parameters
| Characteristic |
Value |
Compression pressure in cylinders, kgf/cm2
| |
| B18B1 | |
Nominal | 13.9 |
The admissible minimum | 9.8 |
The very admissible difference between cylinders | 2.0 |
| B18C1 and B18C5 | |
Nominal | 18.9 |
The admissible minimum | 9.8 |
The very admissible difference between cylinders
| 2.0 |
The pressure of oil (the motor is heated up to the temperature of normal work), kgf/cm2
| |
In the only turns | 0.7 |
With a frequency of rotation of the motor of 3.000 revolutions per minute | 3.5 |
Block of motor
| Characteristic |
Value |
Diameter of cylinders, mm | |
Nominal | 81.001÷81.026 |
Admissible limit | 87.077 |
conicity admissible extreme of the cylinder, mm | 0.051 |
ovality admissible extreme of the cylinder, mm | 0.051 |
Limit the admissible excess of the diameter of the cylinder, mm | 0.254 |
Admissible extreme not planeness of the inter-connected surface, mm | 0.102 |
Pistons and rings of piston
| Characteristic |
Value |
Diameter of pistons, mm | |
Nominal | 80.975÷81.001 |
Admissible limit | 80.975 |
Height of a point of measurement of diameter of a reduction of a skirt, mm | 15.8 |
Slit of landing of the piston in the cylinder, mm | |
Nominal | 0.0102÷0.0406 |
Admissible limit | 0.051 |
The slit of the landing of the piston touches flutes, mm | |
Ring of superior compression | |
Nominal | 0.0457÷0.0711 |
Admissible limit | 0.127 |
According to compression ring | |
B18B1 (Riken)
| 0.0406÷0.0660 |
| B18B1 (Teikoku) | 0.0457÷0.0711 |
| B18C1 and B18C5 | |
Nominal | 0.0457÷0.0711 |
Admissible limit | 0.127 |
Slits in locks of rings of piston, mm | |
Ring of superior compression | |
B18B1 (Riken)
| 0.203÷0.356 |
| B18B1 (Teikoku) | 0.203÷0.305 |
| B18C1 and B18C5 | |
Nominal | 0.203÷0.356 |
Admissible limit | 0.610 |
According to compression ring | |
Nominal | 0.406÷0.559 |
Admissible limit | 0.711 |
Ring of scraper of oil | |
B18B1 (Riken)
| 0.203÷0.508 |
| B18B1 (Teikoku) | 0.203÷0.457 |
| B18C1 and B18C5 | |
Nominal | 0.203÷0.508 |
Admissible limit | 0.711 |
End of inclination and sticks
| Characteristic |
Value |
Play of axial side, mm | |
Nominal | 0.102÷0.356 |
Admissible limit | 0.457 |
Necks of radical loads | |
Diameter, mm | 54.9758÷55.0012 |
| No. N ° 1, 2, 4 and 5 | |
| N ° 3 | |
| B18B1 | |
| B18C1 and B18C5 | |
conicity admissible extreme, mm | 0.0051 |
ovality admissible extreme, mm | 0.0051 |
Limit the admissible thrashing, mm | 0.051 |
Work slit in radical loads, mm | |
Necks 1, 2, 4 and 5 | |
Nominal | 0.0178÷0.0356 |
Admissible limit | 0.051 |
Neck n ° 3 | |
Nominal | 0.0229÷0.0432 |
Admissible limit | 0.051 |
Loads necks conrod | |
Diameter, mm | 44.9758÷45.0012 |
conicity admissible extreme, mm | 0.0051 |
ovality admissible extreme, mm | 0.0051 |
Limit the admissible thrashing, mm | 0.051 |
Work slit in loads conrod, mm | |
| B18B1 | |
Nominal | 0.0203÷0.0381 |
Admissible limit | 0.051 |
| B18C1 and B18C5 | |
Nominal | |
Admissible limit | |
Play of side of side of sticks, mm | |
Nominal | 0.152÷0.305 |
Admissible limit | 0.406 |
Head of cylinders and mechanism valvate
| Characteristic |
Value |
Admissible extreme not planeness of the inter-connected surface of a head, mm | |
Without in favor point | 0.051 |
Repair | 0.203 |
Height of a head of cylinders, mm | 92.939÷93.040 |
Angle of canvas of a facet of saddles valvate | 45 ° |
Angle of canvas of a facet of work of plates of valves | 45 ° |
Width of a cylindrical part (consolation) of the surface of plate that is formed of the valve, mm | |
Entry valves | 1.143 |
Final valves | 1.448 |
Diameter of a nucleus of the valve, mm | |
| B18B1 | |
Entry valves | |
Nominal | 6.5811÷6.5888 |
Admissible limit | 6.553 |
Final valves | |
Nominal | 6.5507÷6.5608 |
Admissible limit | 6.528 |
| B18C1 and B18C5 | |
Entry valves | |
Nominal | 5.4762÷5.4839 |
Admissible limit | 5.58 |
Final valves | |
Nominal | 5.4508÷5.4610 |
Admissible limit | 5.04 |
Internal diameter of the captures of direction of valves, mm | |
| B18B1 | |
Nominal | 6.6046.629 |
Admissible limit | 6.655 |
| B18C1 and B18C5 | |
Nominal | 5.512÷5.537 |
Admissible limit | 5.563 |
Slit of landing nucleus of valves in the direction captures, mm | |
Entry valves | |
Nominal | 0.025÷0.051 |
Admissible limit | 0.076 |
Final valves | |
Nominal | 0.051÷0.076 |
Admissible limit | 0.102 |
Adjusting height of nucleuses of valves, mm | |
| B18B1 | |
| Entry valves | |
Nominal | 40.7645÷41.2344 |
Admissible limit | 41.2344 |
| Entry valves | |
Nominal | 42.7660÷43.2369 |
Admissible limit | 43.4848 |
| B18C1 and B18C5 | |
| Entry valves | |
Nominal | 37.4650÷37.9349 |
Admissible limit | 38.1838 |
| Entry valves | |
Nominal | 37.1653÷37.6352 |
Admissible limit | 37.8841 |
Free spring length valvate, mm | |
B18B1 | |
Entry valves | 42.367 |
Final valves | 47.092 |
B18C1 | |
Entry valves | |
| Day-pupil | 41.046 |
| Nihon Hatsujo | 36.170 |
| Chuo Hatsujo | 36.195 |
| Final valves | |
| Nihon Hatsujo | 41.961 |
| Chuo Hatsujo | 41.935 |
| B18C5 | |
Entry valves | |
| Day-pupil | 43.180 |
| I intern | 36.830 |
| Final valves | |
| Day-pupil | 41.046 |
| I intern | 36.170 |
Efforts of corseting itself of screwed connections, Nanômetro
| Type of connection |
Value |
Pins of coverings of radical loads | |
Stage 1 | 30 |
Stage 2 | |
B18B1 | 76 |
B18C1 and B18C5 | |
Number of coverings n ° 1 and 5 | 76 |
Number of coverings n ° 2, 3 and 4 | 65 |
Nuts of coverings of the lowest leaders of sticks | |
Stage 1 | 19 |
Stage 2 | |
B18B1 | 31 |
B18C1 and B18C5 | 45 |
* Also to see Specifications to Repair without extraction of the car – the model of Full text. |
|
