Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Honda Tsivik
+ Cars of the mark of It Treats Full text and Honda Civic With care
+ Maintenance education
+ Regular maintenance
+ Motor
+ Cooling of system and heating
+ System of provision of power and launch
+ Electric motor equipment
- Systems of control of the motor
   Specifications
   System of diagnostic one of side (OBD) - the beginning of functioning and codes of bad functioning
   Removal and installation PCM/ECM
   Check of usefulness of a state and substitution of the sensor of provision of a valve of butterfly (TPS)
   Check of usefulness of a state and substitution of the sensor of absolute pressure in the oil pipeline (MARCH)
   Check of usefulness of a state and substitution of the sensor of temperature of the soaked air (IAT)
   The check of usefulness of a state and substitution of the sensor of the temperature of cooling the liquid of the motor (EST)
   Check of usefulness of a state and substitution of the sensor of VMT/provision of a doubled end / situation of pistons in cylinders of the motor (TDC/CKP/CYP)
   Check of usefulness of a state and substitution of the sensor of fluctuations of an end of inclination (CKF)
   Check of usefulness of a state and substitution of the discoverer of control of loadings electric (ELD)
   Check of usefulness of a state and substitution of the switch of sensor of pressure in system of hydrofortification of a wheel (PSP)
   Check of usefulness of a state and substitution of the sensor of oxygen (l-probe)
   Check of usefulness of a state and substitution of the sensor of an explosion
   Check of usefulness of a state and substitution of the sensor of speed of the movement of the car (VSS)
   System of stabilization of turns of wasting time - the general information, check of a state and substitution of the valve IAC
   The check of usefulness of a state and substitution of the valve thermosensitive of turns of bystry what wastes time (IT IS ADJUSTED)
   System of a perepuskaniye of the soaked air - the general information, check of a state and substitution of a diaphragm of the valve IAB
   System of the ventilation made work of a case (PCV)
   System of recirculation of the carried out gases (EGR) - the general information, check of a state and substitution of component ones
   System of capture of evaporation of fuel (EVAP) - the general information, check of a state and substitution of component ones
   The catalytic converter - the general information, check of a state and substitution
+ Box of dislocation of gear
+ Union and ends of power
+ Brakes system
+ Support of the triangular form of interruption and direction
+ Body
+ Electric side equipment

The check of usefulness of a state and substitution of the valve thermosensitive of turns of bystry what wastes time (IT IS ADJUSTED)

The OWN valve is installed in some cars models and is in use for the increase in turns of wasting time due to the provision of additional air in the entry oil pipeline in the course of be heating of the motor.

To check

ORDER OF REALIZATION

1. In the moment of the beginning of the check the motor will be in a cold state. Desconecte of the case of regulator a sleeve of air provision (to see the Head of the system of provision of Power and launch).

2. The motor begins in the only turns. Push a finger in case of a regulator and hold tight it to the union joined the OWN valve (companion sees an illustration). The depression has to be felt.

3. Heat the motor up to the temperature check and repeated of normal work. This time to depression has to be going away. The presence of the tension means the incomplete close of the valve what they reason the low level of cooling the liquid or the presence of traffic jams of air traffic on the road of the system of cooling can be – check, to carry out necessary agreements.
4. If the liquid level is normal, and the air is withdrawn completely of the system, substitute the OWN valve.

Substitution

Before the initial implementation of the proceeding, hope for the cooling full of the motor.

ORDER OF REALIZATION

1. Desconecte a hose of the valve, soon results pins of fixation (to see an illustration in top). withdraw the valve together with the rings hunting. At the same time to a zakuporta the open end of a hose for aims of the reduction to the losses minimum of cooling the liquid.
2. Install the valve at the regular place (do not forget of substituting rings of fighter), the pins of fixation of screw and they hold tight us with the necessary effort. In case of the necessity they substitute a collar of the fixation of a hose.
8 check the level of cooling the liquid, in case of the necessity they do the agreement (to see the Front Regular maintenance).