Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car


Honda Tsivik
+ Cars of the mark of It Treats Full text and Honda Civic With care
+ Maintenance education
+ Regular maintenance
+ Motor
+ Cooling of system and heating
+ System of provision of power and launch
+ Electric motor equipment
- Systems of control of the motor
   Specifications
   System of diagnostic one of side (OBD) - the beginning of functioning and codes of bad functioning
   Removal and installation PCM/ECM
   Check of usefulness of a state and substitution of the sensor of provision of a valve of butterfly (TPS)
   Check of usefulness of a state and substitution of the sensor of absolute pressure in the oil pipeline (MARCH)
   Check of usefulness of a state and substitution of the sensor of temperature of the soaked air (IAT)
   The check of usefulness of a state and substitution of the sensor of the temperature of cooling the liquid of the motor (EST)
   Check of usefulness of a state and substitution of the sensor of VMT/provision of a doubled end / situation of pistons in cylinders of the motor (TDC/CKP/CYP)
   Check of usefulness of a state and substitution of the sensor of fluctuations of an end of inclination (CKF)
   Check of usefulness of a state and substitution of the discoverer of control of loadings electric (ELD)
   Check of usefulness of a state and substitution of the switch of sensor of pressure in system of hydrofortification of a wheel (PSP)
   Check of usefulness of a state and substitution of the sensor of oxygen (l-probe)
   Check of usefulness of a state and substitution of the sensor of an explosion
   Check of usefulness of a state and substitution of the sensor of speed of the movement of the car (VSS)
   System of stabilization of turns of wasting time - the general information, check of a state and substitution of the valve IAC
   The check of usefulness of a state and substitution of the valve thermosensitive of turns of bystry what wastes time (IT IS ADJUSTED)
   System of a perepuskaniye of the soaked air - the general information, check of a state and substitution of a diaphragm of the valve IAB
   System of the ventilation made work of a case (PCV)
   System of recirculation of the carried out gases (EGR) - the general information, check of a state and substitution of component ones
   System of capture of evaporation of fuel (EVAP) - the general information, check of a state and substitution of component ones
   The catalytic converter - the general information, check of a state and substitution
+ Box of dislocation of gear
+ Union and ends of power
+ Brakes system
+ Support of the triangular form of interruption and direction
+ Body
+ Electric side equipment


5dfc58ab

The check of usefulness of a state and substitution of the sensor of the temperature of cooling the liquid of the motor (EST)

To check

 ORDER OF REALIZATION

1. Eat it the sensor represents a thermistor (the resistor that the resistance modifies with the modification of the temperature). The modification of the resistance of the sensor practises the straight influence in the vastness of the sign given by the sensor in ECM/PCM. At the same time with the REDUCTION of the resistance of temperature of the sensor IT INCREASES and vice-versa. In the presence in the memory of ECM/PCM of the corresponding code of the bad functioning (to see the System of the diagnostic one of side (OBD) - the beginning of the functioning and the codes of the bad functioning) is necessary to check that a condition of a chain eats and if an electrical system as it must must substitute the sensor.

2. The control of the sensor happens for the measurement of his resistance (companion sees an illustration) in a cold state (10 °C÷27 of °C). then the motor begins and heat it up to the temperature of normal work. The resistance of the sensor will fall.

3. The voltage of provision of measure in the capture of a black-red wire of the capture of an electrical system of the sensor in the included ignition (they do not begin the motor). The result of the measurement will do approximately 5,0 in, otherwise the interval checks a wire in the siege of the sensor to ECM/PCM.

Substitution

Before the initial implementation of the proceeding, hope for the cooling full of the motor.


 ORDER OF REALIZATION

1. Before the installation of the new sensor his part of woodcarving must be injured with a fighter strip of teflon (movie FUM).
2. Pull out a uvula of lock, then exactly the sensor results. For aims of the reduction to the losses minimum of cooling the liquid they screw the new sensor it as soon as possible.

Negotiate he eats it the sensor as it is possible more carefully as his damage is able to practise the perceptible impact in the functioning of a system of provision of power in general.


3. The installation is done upside-down. In the conclusion check the level of cooling the liquid, in case of the necessity they do the corresponding agreement (to see the Front Regular maintenance).