Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Substitution of protective coverings and check of a condition of UNIONS of HP

Component of meeting of an end of power

Internal UNION of HP

Desmontagem

ORDER OF REALIZATION

1st. Cut strips of bandage of the fixation of a covering and move the last of the hinge to the center of an end (companions see illustrations). 1b. Appreciate an extern condition of the old UNION of HP, in the presence of the most light doubts the covering must be substituted. 2. Painting, or through a chertilka they mark the provision of the meeting of the connection of tripodny with the relation to an extern bearer of the hinge. Remove a bearer of the load. 3. Withdraw a ring of spring lock of an extern pin of an end. 4. Embarrassment that loads rolls, to have injures them with an insulating tape (companion sees an illustration), soon lower the meeting tripodny of an end, having used the hammer and a current of brass. 5. Take a ring of lock and withdraw an old protective covering of an end of power.

To check

ORDER OF REALIZATION

1. Carefully withdraw lubricating aspects of an extern bearer of the hinge and the cavities of the load of tripodny. In series, not to be mixed, withdraw each one of sections of the meeting tripodny and wash out rolls of the solvent of loads of needle. 2. Check rolls, loads, the part of load of the meeting tripodny and an extern bearer of the hinge of the existence of signs of the excessive use of cavities, zadir, slits and other mechanical damages. In case of the necessity they substitute the UNION of HP.

Meeting

ORDER OF REALIZATION

1st. Roll up openings of a pin of an end of an insulating tape of the protection is able against a new protective covering of UNIONS of HP against reductions (companion to see an illustration). 1b. An end puts a covering, withdraw an insulating tape and put an internal ring of lock (companion sees an illustration). 2. Meeting tripodny put in an end. 3. Register the meeting tripodny for an extern ring of lock (companion sees an illustration). 4. The fat with the special dense lubricant inside roll loads for their aims of the temporary fixation in the elements of load of the meeting tripodny (companion sees an illustration). The trace that each roll established strictly at the ancient place. If the rolls equip a rectangular form lysky, trace that was established by these lyska to an end. 5. The half fills an extern bearer of the hinge the complete handed lubricant of a new covering. To remain of the lubricant fills a covering. Establish an extern bearer in an end (companion sees an illustration). The fairness of trace of the combination of the etiquettes of the mutual provision of a bearer and the tripodny load put in the course of is demolished. 6. Put sponges of covering in flutes in an extern bearer of the hinge and a body of an end, soon adjust the length of the meeting of an end according to the demands of Specifications (companion sees an illustration). 7. Having exposed the length of end, when was left gone out the air of bass of a covering, having hooked up his day-pupil (bigger diameter) it borders the rude screwdriver (companion sees an illustration). Try not to damage a covering. 8th. Fix a covering for new strips of bandage (companions see illustrations): do not bend the free end of a strip of bandage behind. 8b. Then do not bend uvulae of lock. 9. Install the meeting of an end in the car (to see the Removal and the installation of ends of power).

Extern UNION of HP

Desmontagem

ORDER OF REALIZATION

1. The work according to the educations affirmed in top that they withdraw the internal UNION of HP of an end of power and classify it. 2. If the end is equipped of a damper of loadings dynamic, it marks with the painting the provision of the exterior edge of the meeting that is loosened about an end, when a collar was then cut and withdraws a damper. Substituting component it is necessary to follow the trace of the observance of the distance between a covering of the internal UNION of HP and a damper (to see Specifications). 3. Cut strips of bandage and withdraw a protective covering of the UNION of HP of an end. THE extern UNION of HP is not subject to desmontagem and removal of an end.

To check

ORDER OF REALIZATION

1. Carefully one wash HP out internally and extern JOIN the solvent, soon dry them with the use of compressed air. When it uses compressed air do not forget of putting wide eyes! Since the extern UNION of HP is not subject to the desmontagem, his removal of aspects of old lubricant and solvent is joined with certain difficulties, nevertheless it has to be done very carefully. 2. Becoming a covering of hinge below several corners, attentively study a condition of scamp, bearers and a separator of the load (companion sees an illustration). In case of the detection of defects they substitute the meeting of an end.

Meeting

ORDER OF REALIZATION

1st. Roll up openings of a pin of an end of an insulating tape of the protection is able against a new protective covering of UNIONS of HP against reductions (companion to see an illustration). An end puts a covering, withdraw an insulating tape, soon fill the lubricant enclosed in a remnabor in a covering. Give a covering in the position and register it new bandage strips. 2. Meeting tripodny put in an end. 3. Register the meeting tripodny for an extern ring of lock (companion sees an illustration). 4. In the corresponding complete set they establish a damper of dynamic loads of an end. The fairness of trace of the combination of the etiquettes of landing put in the course of is demolished. When it substitutes an end it takes care of the observance of the necessary distance of a damper to the internal UNION of HP (to see Specifications). Establish a new collar of fixation. 5. Wash out and join the meeting of the internal UNION of HP. Install the meeting of an end of power in the car (to see the Removal and the installation of ends of power).