Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Removal and installation of ends of power

Removal

ORDER OF REALIZATION

1. Take away a hat of edge. If the nut stupichny is fullered, do not bend a fillet of lock / uvula through a punch of center or a chisel (companion sees an illustration). 2. Weaken a nut stupichny through a face key with the equipped walk of a long collar (companion sees an illustration). 3. Weaken nuts of the fixation of the corresponding advanced wheel, the car and establish it to a poddomkratta in stakes. Withdraw a wheel. The oil of transmission of fusion / ATF (to see the Front Regular maintenance). 4. Desconecte a damper fork of there moistens the meeting and the lever of control more decrease of a support of the triangular form of interruption (to see the Chief Podvesk and driving). 5. There launches the lever of control more decrease of a support of the triangular form of interruption of a rotary fist (to see the Chief Podvesk and driving). Now finally give a nut stupichny. 6. Reject the meeting stupichny on the outside, launching of him a pin of an end of power (companion seeing an illustration). If the power end "was soured" and there does not give in the extraction of a nave, blow to his end face with the hammer with the gentle living creature. Tie the extern end of an end of a wire is able to some of elements of support of the triangular form of interruption, having removed with this unnecessary loads of the meeting of the internal UNION of HP. 7th. When there hooked exactly the lever, throw up the internal end of an end of power of the main transfer of the transmission, or (model of Full text) of the meeting of an intermediary end. Like the hill of lever that must be introduced in a slit between a covering of the internal UNION of HP and a case a transmission / support of the load of an intermediary end perfectly is going to approach (companions see illustrations). 7b. Being maintained for UNIONS of HP, exactly take the meeting of an end of power of bass of the car. To avoid that the damage of an epiploon of an intermediary end / differential tries to maintain the internal UNION of HP in the horizontal position until the pin of an end is not launched of a landing nest finally.

Installation

ORDER OF REALIZATION

1st. Withdraw a ring of spring lock of the internal end of an end of power and it is substituted by new (companions see illustrations). 1b. The sponges of fat of the epiploon of an intermediary end / differential with the universal lubricant, then exactly bring an end of power to the regular situation, maintaining it for UNIONS of HP. 2. Carefully fill the pin of HP internal JOINT provided with openings in a landing nest in a case of transmission or intermediary end (model of Full text). It is secured what the lock ring bolted confiantemente in a landing flute. 3. Lightly the fat with the universal lubricant of an opening of a pin of the extern UNION of HP, I delay on the outside stupichny meeting and exactly the end of an end fills out it. 4. There fills a hair clip of hair of a spherical support of the lever of control more decrease of a support of the triangular form of interruption in a rotary fist and hold tight a nut with the necessary effort (to see Specifications to a Chief Podvesk and driving). Do not forget of substituting the quiff. Establish at the place a fork that is loosened (to see the Chief Podvesk and driving). 5. Twist a nut stupichny (in case of the necessity they do not forget of substituting a lavador of lock) and strongly hold tight it. The final pressure of a nut stupichny with the necessary effort is done after lowering of the car in the land. 6. Seize the case of the internal UNION of HP (not for an end) and pull it on the outside, checking the confidence of the fixation of a pin in the transmission. 7. Establish at the place a wheel, fix it for nuts and lower the car in the land. 8. The delay with the necessary effort wheel (to see Specifications to the Front Regular maintenance) and the nuts stupichny. Through a punch of fuller center a nut stupichny. Establish at the place a hat of edge. 9. Fill out in the transmission the necessary amount of oil of the necessary degree (to see the Front Regular maintenance).