Honda Tsivik
+ Cars of the mark of It Treats Full text and Honda Civic With care
+ Maintenance education
+ Regular maintenance
+ Motor
+ Cooling of system and heating
+ System of provision of power and launch
+ Electric motor equipment
+ Systems of control of the motor
+ Box of dislocation of gear
+ Union and ends of power
- Brakes system
Specifications
System of antiblockade of brakes (ABS) - the general information and codes of bad functioning
Substitution of shoes of brake of mechanisms of brake of disc
Removal, repair and installation of supports of mechanisms of brake of disc
Check of a state, removal and installation of a disc of brake
Substitution of boots of mechanisms of brake of drum of rear wheels
Removal and installation of cylinders of wheel
Removal and installation of the cylinder of main brake
Check of a state and substitution of lines of brake and hoses
Extraction through bomb of the system of brakes
Check of usefulness of functioning / tension, removal and installation of meeting of the amplifier of vacuum of brakes
Agreement of the brake of parking
Substitution of a thread (threads) of the walk of the brake of parking
Check of usefulness of functioning, substitution and agreement of the switch of sensor of lights of the brake
Check of usefulness of functioning and substitution of the switch of sensor of level of fluid of brake
+ Support of the triangular form of interruption and direction
+ Body
+ Electric side equipment
|
Removal, repair and installation of supports of mechanisms of brake of disc
|
|
Remember that the powder produced in the course of the operation of mechanisms of brake can contain the extremely unhealthy asbestos of the person. Do not take the compressed air of powder in absolute and do not inhale, – in the mechanisms service it put a protective mask or a respirator. Do not use to be scratched of component ones of the gasoline of system of brakes or the solvents in an oil base in absolute, – only they apply detergents of company or alcohol of metilo! |
Removal
|
|
1. Weaken nuts of wheel. A front / coast of the car also establishes it the Poddomkratta in stakes. Withdraw wheels.
|
|
2. In the moment of the removal of a support of the mechanism of brake of disc of a few back a wheel takes the quiff and desconecta a thread of the walk of the brake of parking of the executive lever (companion sees an illustration). |
|
|
3. Desconecte of a support to hydraulic line, for aims of the reduction to the minimum of losses of fluid of brake, and also, to avoid the blow in a way of the dirt to a nipple connection zakuporta (companion to see an illustration). |
4. Withdraw a support (to see the Substitution of shoes of brake of mechanisms of brake of disc). |
|
Repair Support of the mechanism of brake of an advanced wheel
Support of Akebono
Support of Nissin
|
|
1. The options of a drawing of supports of mechanisms of brake of disc companions give themselves in illustrations in top.
2. Put a support in a pure bank. If in a few spring bearers of support of blocks they are established, remember his agreement of the meeting, then withdraw. If the boot of the piston is registered through a spring ring, withdraw it, having hooked the screwdriver up.
3. Withdraw a boot.
4. Before taking the piston, put between him and a wall of a support to wooden grindstone (for the protection of the piston). The piston puts itself for out for the provision of air pressed in the union of connection of a hose of brake. The air pressure will be least.
|
|
Look that the fingers did not appear between the piston and a support! |
5. Appreciate a condition of surfaces of work of the piston and cylinder in a support. In case of the identification of cavities, the zadir, asperezas and zones with the modified coloration, substitute the meeting of a support.
6. In the order of work of component ones they take of a flute in the cylinder a fist of sleeve of piston, when the plastic wooden instrument hooked it up or (the use of the metal instrument can lead to the damage of a mirror of the cylinder).
7. Put captures out of to fix pins of a support of eyes in case of the last one. In the corresponding complete set, previously withdraw the established protective coverings of rubber of two sides.
8. Wash out all the retired details special detergent. Prepare the play of repair that corresponds to a support drawing. Moisten a new fist of sleeve of the piston with the fluid of pure brake and fill it in the flute in the support cylinder. It is secured what is not overinjured the fist of sleeve.
9. If the boot of the piston is established without ring of spring lock (the supports of the Nissin), fill a boot in the superior flute in the support cylinder. Perfection of trace of landing of a flange of a boot in a flute.
|
|
10. Polish the piston with the fluid of pure brake, exactly push it for a new boot and fill out the cylinder of support (the piston will enter in the cylinder with a small resistance). One secures that the boot came to a landing flute in the piston (companion saw an illustration). |
11. If to fix of a boot the ring of spring lock (the supports of the Akebono) it if are supplied, it establishes it at the place. One secures that the boot came to a landing flute in the piston.
12. The pins of fat of a support for the lubricant of silicon enclosed in a remnabor and they fill us in case of which eyes. Do not forget of establishing protective coverings. |
|
Support of the mechanism of brake of a rear wheel In order that the special instruments are demolished of supports of the mechanism of brake of a rear wheel they are needed in view of what, the realization of his repair will be reasonable to collect to specialists of the service of the car. Installation
|
|
