Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Substitution of shoes of brake of mechanisms of brake of disc

Mechanisms of brake of advanced wheels

ORDER OF REALIZATION

1. Through an armband they drown the piston in the support cylinder, having supplied the free space through that necessary for the installation of the new blocks that have great thickness (companion sees an illustration). In a piston utaplivaniye in a level of liquid of support in the tank GTTs it will increase, – clock that did not begin to flood, in case of the bomb of necessity it had been an excess. 2nd. Before the beginning they are demolished of component ones certainly wash to us a special cleaner (companion sees an illustration). 2b. There results the lowest pin of a support (the lowest arrow); head the arrow it showed a hollow pin of the connection of nipple of a hose of brake; the hose is subject to a lack of interest only there if will be a need for the removal of a support of the car. 2 pages. Raise a support, having supplied through that the access to brake shoes. 2nd. To fix of a support in the lifted situation they tie it a wire to a torture of support of the triangular form of interruption. 2e. Withdraw a shoe of extern brake with the placing agreement. 2f. Withdraw a shoe of internal brake (in any models the internal block is not equipped of the placing agreement). 2g. Withdraw the top and lower spring bearers of blocks and check his states (it remembers that the internal block also is equipped by bearers). 2 h. The confidence of trace of the landing of spring bearers in the flutes in a support of the triangular form of the anchor of a support (in case of the necessity they substitute bearers). 2i. I intern (in the left) and extern brake shoes with the agreement of the placing of an extern block (in some models of Full text of last years of the launch the internal block also if it supplies with the placing agreement). 2j. Before the installation of adjusting the placing they polish the rear party of blocks with the structure antivizgovy special. 2k. Establish a shoe of internal brake (the uvulae follow the trace of this in the top and the lowest ends of the block entered in reciprocal flutes and were registered confiantemente by spring bearers). 2l. Establish a shoe of extern brake (placing will be adjusted not to be included in the packet of new blocks, establish in a block the old placing). 2 m. Before lowering a support they do not forget of checking a condition of protective coverings of the fingers of direction; substitute the damaged coverings. 2n. The extern finger of a support before the installation must be smoothed and be polished with the heat-resistant lubricant; the same thing must be done with the fixation pin more low from a support This demand only belongs to the Civic models with pins of humeral long and the fixed superior fingers [a support of the type 2056]). 2 lakes. Lower a support in the regular situation (if the remains of piston against an internal block, an armband pulls out it in the cylinder). 2 rubles. Screw the lowest pin of a support and hold tight it with the necessary effort.

Mechanisms of brake of rear wheels

ORDER OF REALIZATION

1st. Result fixation pins and withdraw the filter of support. 1b. Result two pins of the fixation of a support. 1 page. Withdraw a support of a support of the triangular form of the anchor and tie it a wire to an element of support of the triangular form of interruption – tries not to allow the tension of a hose of brake. 1d. Withdraw an extern block with the placing agreement. 1e. Withdraw an internal block with the placing agreement. 1f. Withdraw of a few bearers of support of blocks (the lowest bearer shows off, superior looks and it is established in the same way). 2. Cover the rear party of new blocks with the structure antivizgovy special (companion sees an illustration). The education of the use of ways is printed normally out in a barrel wall. 3. Establish the placing of agreement in blocks. 4. Establish bearers of blocks in a support of the triangular form of the anchor of a support. Polish bearers of blocks with a fine layer of the lubricant of silicon. 5. Establish new shoes of brake with the placing agreement in a support of the triangular form of the anchor of a support. 6. Through the claws turn the piston, having drowned it in the support cylinder for aims of supplying the necessary free space under the installation of new shoes of brake (companion to see an illustration). In the beginning drown the piston to the bottom of the cylinder, it result behind so that during the installation of an internal block his influx came to one of selections in the surface of face of the piston. The trace that as a consequence of the rotation of the piston the boot did not lose shape. 7. Having finished the meeting of the mechanism of brake, install at the place his filter.

Brake mechanisms of advanced and rear wheels

ORDER OF REALIZATION

1. Establish to the place of a wheel, lower the car in the land and hold tight nuts of the fixation of wheels with the necessary effort (to see Specifications to the Front Regular maintenance). 2. Several times hold tight out a pedal of brake and (if modified behind it blockades) the lever of the brake of parking for aims of the shrinking of blocks in a disc. 3. Check that the level of fluid of brake, in case of the necessity they do the corresponding agreement (to see the Front Regular maintenance). Before beginning the normal operation of the car, one secures of the usefulness of the functioning of the system of brakes.