Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Check of a state, removal and installation of a disc of brake

Check of a state

ORDER OF REALIZATION

1. Weaken nuts of fixation to the Coca bush, a poddomkratta the car and establish it in stakes. Withdraw the corresponding wheel, soon screw the couple of nuts behind in the fixation of hair clips of hair, having enclosed below them lavadores of 3 mm of thickness for aims of fixing of a disc of brake (if two screws of the fixation of a disc are still not poured, the necessity of a navorachivaniye of nuts disappears). When it checks a disc of the mechanism of rear brake it does not forget of launching the brake of parking. 2. Withdraw a support of brake (to see the Removal, the repair and the installation of supports of mechanisms of brake of disc) and a wire ties it to the part to an element of support of the triangular form of interruption, without desconectar a brake hose. 3. Carry out the visual control of a condition of a surface of work of a disc (companion sees an illustration). The easy defects can be removed through a paper of emery of fine granulation. For the furrows removal more than 0,38 mm to bottom the disc must be subjected to an in favor point. 4th. If during the pedal pulsations they brake if they noticed, it is necessary to appreciate the size of a thrashing of side of a disc of brake. Fix the instrument of measuring of disc of the diver's type (DTI) in the distance approximately 12,7 mm of the exterior edge of a disc (companion to see an illustration). 4b. Cancel the device and begin to make spinning a disc. The result of the measurement must not exceed the limit of the admissible variety stipulated in Specifications, otherwise the disc has to happen to an in favor point. The authors of the present manual recommend to do an in favor point of discs in spite of his state for aims of the removal of any surface of work of defects. Since last resource is possible there is limited by the processing of a disc a paper of emery of fine granulation. 5th. In an in favor point of a disc it is necessary to pay the special attention to the observance of demands of Specifications to his least admissible thickness. In a surface of face of a disc the corresponding marking is supplied (companion sees an illustration). 5b. The measurement of the thickness of a disc is executed through a micrometer (companion sees an illustration).

Removal

ORDER OF REALIZATION

1st. Result two pins of the fixation of a support of the triangular form of the anchor of a support to a rotary fist (companion sees an illustration). 1b. Or (in the mechanism of brake of a rear wheel) pins of fixation of a support of triangular form to the longitudinal lever of a support of the triangular form of interruption. Withdraw a support of triangular form. 2nd. Withdraw two nuts of wheel used to fix of a disc in a nave / they result two screws of fixation (companion sees an illustration). 2b. Withdraw a disc of a nave of wheel. If the disc "prickled" to a nave, it can corset itself out for a vvorachivaniye in the fixation of the openings of the couple of pins of the convenient size (companion sees an illustration). 2c. Hold tight pins exactly and gradually until the disc completely is not launched. In the moment of the removal of an attempt of disc not to damage a woodcarving of hair clips of hair of the fixation of a wheel (companion to see an illustration).

Installation

ORDER OF REALIZATION

1. Exactly there puts a disc a nave (again they try not to damage hair clips of hair of wheel). Screws of fixation of screw. 2. Install a support of the triangular form of the anchor of a support in a walk. Hold tight pins of the fixation of a support of triangular form and a support for the necessary effort. 3. Establish at the place a wheel, lower the car in the land and hold tight nuts of wheel with the necessary effort (to see Specifications to the Front Regular maintenance). Several times squeeze out a pedal of brake / they lift the lever of the brake of parking for aims of the shrinking of blocks in a disc. If the brake hoses not if desconectaram, the necessity of a prokachivaniye of the hydraulic system goes away. Before the initial operation of the car, one secures of the usefulness of the functioning of brakes.