Honda Civic/Acura Integra

2nd. The drawing of the mechanism of brake of drum happens in an illustration in top. Withdraw the drum of brake of a nave. The drum has to be withdrawn somewhat freely, in case of difficulties, exactly to explore he the hammer with the gentle living creature, or it will support in the woodcarving of the couple of openings of pins of M8 (companion to see an illustration).

4th. To work according to the educations affirmed besides that that they carry out the control of a condition of component ones and substitute boots of brake. Law strictly in the stipulated order. Remember that four boots of both mechanisms of brake have to be substituted at the same time.

4b. Before the beginning they are demolished of component ones, wash out a special cleaner to us, soon they dry (DO NOT TAKE the COMPRESSED AIR of POWDER OF BRAKE IN ABSOLUTE!).

4 pages. The screwdriver pulls out the spring of direction down, soon develop a finger of the anchor to parallel lock to a groove in one spring – the last thing at the same time will jump besides a boot.

4d. Withdraw the meeting of shoe of a council of brake (the nave is for retired descriptive reasons).

4e. Desconecte a spring of union.

4f. Delay one spring in a thread of the walk of the brake of parking so that there was an opportunity for seizing a thread bokorezama, maintaining one spring in the pressed state (try not to cut a trunk); now desconecte a tip of end of the executive lever of the brake of parking.

4g. Turn the executive lever of the brake of parking, taking it of a rear brake boot – at the same time the fork of a pin of agreement of a level razzhimny has to be launched of the landing flute in a boot that it will allow to separate boots.

4th. Withdraw the lever and a spring of the automatic regulator of an advanced boot of brake.

4i. Withdraw an armband and desconecte the executive lever of the brake of parking of a rear boot (do not lose the lavador of inclination established below a ring of lock).

4j. A new rear boot is joined to the lever (do not forget of enclosing a lavador of inclination below an armband); the claws hold tight the ends of an armband together.

4k. Clean a pin of agreement and the forks of the level razzhimny, soon polish them with the heat-resistant lubricant.

4l. Hook in a spring of the automatic regulator of an opening in a new advanced boot, soon fills a finger of lever in another special opening in a boot.

4 m. Fill a short fork of a level razzhimny in the groove in an advanced boot (the fairness of trace of the entry of a fork in the gear with the lever of the automatic regulator.

4n. Adhere to spring of superior union so much to curb boots, to divide the lowest ends of boots as it will fill a fork of a level razzhimny in a groove in a rear boot (the fairness of trace of an agreement of an edge of step of a fork).

4 lakes. Polish the surfaces of a council of brake to contact to boots with the heat-resistant lubricant.

4P. Bokorezami squeezes a spring of a thread of driving of the brake of parking (do not cut a thread) and, maintaining it in such situation, one an end tip to the executive lever.

4q. Establish the meeting of shoe in a council of the mechanism of brake, having put superior extremes of boots in grooves in pistons of the cylinder of wheel; one to spring of lower union to boots.

4r. Fingers of anchor of step during openings in a council of brake and boots, establish the springs of direction; develop fingers, having registered springs; the trace that the spring of a thread of the walk of the brake of parking and the lowest spring of union acquired below levels of a support of the triangular form of the anchor as it is shown in a picture.

5. Before the installation of the unsteady movement the existence is necessary to check it of zadir, furrows, aspects of overheating and other defects. In the moment of the identification of serious damages that the aspects cannot remove prosecuting of a drum with a paper of emery of fine granulation that the drum must give itself to an in favor point (with the observance of the very diameter of admissible repair). If it is not possible to do the in favor point of a drum without the violation of demands to the very admissible internal diameter (one works out in a drum – they see an illustration companion), it is necessary to do his substitution. If it is not possible to do an in favor point of drums, at least carefully smooth them when there is working surfaces a paper of emery of fine granulation.

The authors of the present manual recommend to do an in favor point of drums in spite of his state for aims of any removal of defects and the elimination of ovality.