Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Removal, check of a state and installation of a belt that distributes the gas and cog-wheels of GRM drive

Removal

ORDER OF REALIZATION

1. Desconecte a negative wire of the battery. If the stereosystem established in the car if it equips of a security code before desconectar the battery they secure what has the correct combination of the entry of the system sound in the action! 2. Support behind wheels you put that you were antishowing and strongly lift the brake of parking. 3. Weaken nuts of the fixation of advanced wheels, soon a front of the car and establish it to a poddomkratta in stakes (to see the Front Regular maintenance). 4. Withdraw advanced wheels and protection of a case of the motor. 5. Support a monkey to unity of power (for aims of the distribution of the load they put the wooden grindstone between a head of a monkey and the trundle bed of a case of the motor). 6. Withdraw an arm of the superior support of the motor (to see the Check of a state and the substitution of the support of a support of the triangular form of interruption of the unity of power). 7. Result when they were taken of spark and take away belts of driving (to see. Regular maintenance). 8. Otboltite to direction bomb also moves it to the part, without separation hydraulic lines (to see the Chief Podvesk and driving). 9. Take the probe of the measurement of oil of reason. 10. Bring the piston of the first cylinder in the provision of VMT of the end of a step of the compression (to see the Reduction of the piston of the first cylinder in the provision of the superior dead point (TDP)). The inclination end must be become alone in the normal direction (in reverse sense to the movement of the pointers of the clock) – the failure of following this demand will lead to the violation of agreements of a belt that distributes the gas. 11. There withdraws the superior covering of a belt of GRM drive (companion sees an illustration). 12. Fighter of an advanced part of the motor an intermediary video of an arm. 13. Through a chain or block of key of strip a pulley of a kolenchatogoval of a provorachivaniye, then a key of face weakens a pin of the fixation of a pulley (companion sees an illustration). 14. Withdraw a pulley of a pin of an end of inclination. 15. Catch the telephone of direction of the probe of measuring on an advanced part of the motor. 16. Withdraw the lowest covering of a belt that distributes the gas. 17. If the old belt will be in the good repair and if it will establish at place, mark with chalk or white painting to direction of his rotation and situation about cog-wheels of the end (companion sees an illustration). 18. Weaken a pin of the fixation of a natyazhitel of a belt that distributes the gas (companion sees an illustration). Having pulled out a natyazhitel, weaken a belt, then again hold tight a pin. Withdraw the sensor of fluctuations of an end of inclination (to see at the same place), soon gets rid of a cog-wheels belt. If the removal of a belt is done for aims of the realization of the substitution of an epiploon of an end of inclination, get rid of a pin of the last one of a cog-wheel and an internal guide of a belt (to see the Substitution of an advanced epiploon of an end of inclination). 19. There if will be a need for the removal of the axle or substitution of his epiploon, pass the great screwdriver through an opening in an end cog-wheel for aims of blockading it of a provorachivaniye, then a key of face weakens a pin of fixation and withdraws a wheel. Take a segment spline of an axle pin.

To check

ORDER OF REALIZATION

1. Manually check the freedom of the rotation of a roll of a natyazhitel, soon pull it here and there, checking the existence of a play of side in the load (companion seeing an illustration). The incorrect roll is subject to the substitution. 2. Attentively examine a belt that distributes it the gas of two sides, when it is checked by the existence of signs of the use specially persistent (walls of the teeths), split, parliament, atritos and aspects of lubricating (companion to see an illustration). The incorrect belt is subject to the compulsory substitution. If only the race of the motor is not really small, the substitution of a belt is recommended being done in spite of his state. Do not install an old belt in the motor in absolute, in order that any hundred of per cent is I do not hold of the usefulness of his state.

Installation

ORDER OF REALIZATION

1. If withdrawn, it establishes in cog-wheels of place of the end (one does not forget of a segment spline of a wheel of the axle and an internal guide of a belt in an inclination end). Hold tight a pin of the fixation of a cog-wheel of the axle with the necessary effort (to see Specifications). 2. Before the installation of a belt it are secured what the cog-wheel of the axle establishes for an etiquette in the form of a point or letters of. Two agreement etiquettes will appear in the airplane of a surface of a head of cylinders (companion sees an illustration). 3. Temporarily establish at place and embarrassment for a pin a pulley of an end of inclination, soon become an end (if one slammed) so that the agreement etiquette in his cog-wheel went with the answer rate in case of the bomb of oil (companion was seeing an illustration). 4. Densely there puts a belt a cog-wheel of an end of inclination, soon execute it below a roll of a natyazhitel and around cog-wheels of the water bomb and axle (companion sees an illustration). 5. Weaken a pin of a natyazhitel, having supplied a tension of belt, then temporarily hold tight a pin. 6. Exactly six times become an end of inclination in the direction in reverse sense to the movement of the pointers of the clock, soon one secures of the fairness of an agreement of adjusting etiquettes of a cog-wheel of the axle. If the inclination end will be turned with breaks of the enemy lines or if it pinched, it is not necessary to apply the force as it can lead to the valves damage they take in us on the bottoms of pistons (if the agreement is lowered). Take away a belt and repeat the proceeding, paying the special attention to the combination of adjusting etiquettes. 7. Since the agreement of the effort of a tension of a belt weakens the half of way (of 180 °) a pin of a natyazhitel and it becomes an end of inclination in the direction in reverse sense to the movement of the pointers of the clock in three teeth of the provision of VMT. Now hold tight a pin with the necessary effort. 8. Establish at the place all the component ones that were withdrawn in the course of are demolished. 9. Adjust efforts of a tension of the driving of belts (to see the Front Regular maintenance). 10. The motor begins and check the usefulness of his functioning.