Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Removal, check of a state and installation of a belt that distributes the gas and cog-wheels of GRM drive

Removal

ORDER OF REALIZATION

1. Desconecte a negative wire of the battery. If the stereosystem established in the car if it equips of a security code before desconectar the battery they secure what has the correct combination of the entry of the system sound in the action! 2. Support behind wheels you put that you were antishowing and strongly lift the brake of parking. 3. Weaken nuts of the fixation of advanced wheels, soon a front of the car and establish it to a poddomkratta in stakes (to see the Front Regular maintenance). 4. Withdraw advanced wheels and protection of a case of the motor. 5. Support a monkey to unity of power (for aims of the distribution of the load they put the wooden grindstone between a head of a monkey and the trundle bed of a case of the motor). 6. Withdraw an arm of the superior support of the motor (to see the Check of a state and the substitution of the support of a support of the triangular form of interruption of the unity of power). 7. Result when they were taken of spark and take away belts of driving (to see. Regular maintenance). 8. Otboltite to direction bomb also moves it to the part, without separation hydraulic lines (to see the Chief Podvesk and driving). 9. Withdraw the mechanism of actuation of a system of control of the speed (tempostat) (to see the electric equipment of Front Side). 10. Bring the piston of the first cylinder in the provision of VMT of the end of a step of the compression (to see the Agreement of seats). The inclination end must be become alone in the normal direction (in reverse sense to the movement of the pointers of the clock) – the failure of following this demand will lead to the violation of agreements of a belt that distributes the gas. 11. Discover a head of cylinders (to see the Equipment and administrations in the hall). 12th. Withdraw the central covering of a belt that distributes the gas. 12b. Withdraw the lowest covering of a belt that distributes the gas. (companions see illustrations). The superior covering goes with a front covering. 13. The way half weakens a pin of a natyazhitel of a belt (companion sees an illustration). Having pulled out a natyazhitel, weaken a belt, then again hold tight a pin. 14. Through a chain or block of key of strip a pulley of an end of inclination of a provorachivaniye, then a key of face weakens a pin of the fixation of a pulley (companion sees an illustration). 15. Withdraw a pulley of a pin of an end of inclination. 16. If the old belt will be in the good repair and if it will establish at place, mark with chalk or white painting to original direction of his rotation and situation about cog-wheels of the end (companion sees an illustration). 17. Weaken a pin of the fixation of a natyazhitel. Having pulled out a natyazhitel, weaken a belt, then again hold tight a pin. Get rid of a cog-wheels belt and take away it of the motor. If the removal of a belt is done for aims of the realization of the substitution of an epiploon of an end of inclination, get rid of a pin of the last one of a cog-wheel and an internal guide of a belt (to see Systems of security). 18. There if will be a need for the removal of axles or substitution of his epiploons, pass the great screwdriver through an opening in a cog-wheel of the corresponding end for aims of blockading it of a provorachivaniye, then a key of face weakens a pin of fixation and withdraws a wheel. Take a segment spline of an axle pin. The wheel of the second end is withdrawn in a similar way.

To check

Try not to allow provorachivaniye of cog-wheels operated with crank or axles in the tuck - of the belt of GRM drive to avoid the damage of valves as a consequence of his punch with the pistons bottoms.

ORDER OF REALIZATION

1. Manually check the freedom of the rotation of a roll of a natyazhitel, soon pull it here and there, checking the existence of a play of side in the load (13 seeing an illustration to the paragraph). The incorrect roll is subject to the substitution. 2. Attentively examine a belt that distributes it the gas of two sides, when it is checked by the existence of signs of the use specially persistent (walls of the teeths), split, parliament, atritos and aspects of lubricating (companion to see an illustration). The incorrect belt is subject to the compulsory substitution. If only the race of the motor is not really small, the substitution of a belt is recommended being done in spite of his state. Do not install an old belt in the motor in absolute, in order that any hundred of per cent is I do not hold of the usefulness of his state.

Installation

ORDER OF REALIZATION

1. If withdrawn, it establishes in cog-wheels of place of the end (one does not forget of the segment splines of wheels of axles and an internal guide of a belt in an inclination end). Hold tight pins of the fixation of cog-wheels of axles with the necessary effort (to see Specifications). 2. Before the installation of a belt it are secured what the axles cog-wheels establish for an etiquette of. The etiquettes adjust that they have to go with the rate in a rear cape of a belt (companion sees an illustration). In the moment of the emergence of the resistance immediately they stop an end provorachivaniye to avoid the damage of valves as a consequence of the punch with the pistons bottoms. Exactly correct the provision of cog-wheels of axles, soon repeated attempt. 3. Temporarily establish at place and embarrassment for a pin a pulley of an end of inclination, soon become an end (if one slammed) so that the agreement etiquette in his cog-wheel went with the answer rate in case of the bomb of oil (companion was seeing an illustration). 4. Densely there puts a belt a cog-wheel of an end of inclination, soon execute it below a roll of a natyazhitel and around cog-wheels of the water bomb and axles. Weaken a pin of a natyazhitel, having supplied a tension of belt, then temporarily hold tight a pin. 5. Exactly six times become an end of inclination in the direction in reverse sense to the movement of the pointers of the clock, soon one secures of the fairness of an agreement of adjusting etiquettes of cog-wheels of axles (to see illustrations in top). If the inclination end will be turned with breaks of the enemy lines or if it pinched, it is not necessary to apply the force as it can lead to the valves damage they take in us on the bottoms of pistons (if the agreement is lowered). Take away a belt and repeat the proceeding, paying the special attention to the combination of adjusting etiquettes. 6. Since the agreement of the effort of a tension of a belt weakens the half of way (of 180 °) a pin of a natyazhitel and it becomes an end of inclination in the direction in reverse sense to the movement of the pointers of the clock in three teeth of the provision of VMT. Now hold tight a pin with the necessary effort (to see Specifications). 7. Establish at the place all the component ones that were withdrawn in the course of are demolished. 8. Adjust efforts of a tension of the driving of belts (to see the Front Regular maintenance). 9. The motor begins and check the usefulness of his functioning.