Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Honda Tsivik
+ Cars of the mark of It Treats Full text and Honda Civic With care
+ Maintenance education
+ Regular maintenance
- Motor
   + Repair of the motor without extraction of the car - the Civic model
   + Repair of the motor without extraction of the car - the Full text model
   - General and repairs of capital of the motor
      General information
      Check of pressure of oil
      Check of pressure of compression in cylinders
      Diagnostic of a condition of the motor with use of the measure of vacuum
      Removal of the car of the unity of power - preparation and measured by precaution
      Removal and installation of the motor
      Alternative versions of schemes of repair of recuperation of the motor
      Order of desmontagem of the motor for preparation he to capital repairs
      Desmontagem of a head of cylinders
      To clean and check of a condition of a head of cylinders
      Valves service
      Meeting of a head of cylinders
      Removal of conrod and piston meetings
      Removal of an end of inclination
      Cleaning of the block of the motor
      Check of a condition of the block of the motor
      Honingovaniye of mirrors of cylinders
      Check of a condition of component ones of conrod and group of piston
      Check of a condition of an end of inclination
      Check of a state and selection of insertions of radical loads and conrod of an inclination end
      Order of meeting of motor
      Installation of rings of piston
      Installation of an end of inclination and check of slits of work of radical loads
      Substitution of a few back epiploon of an inclination end
      Installation of conrod and meetings of piston and check of size of slits of work in loads conrod of an inclination end
      Broken of proof and running in of the motor after capital repairs
+ Cooling of system and heating
+ System of provision of power and launch
+ Electric motor equipment
+ Systems of control of the motor
+ Box of dislocation of gear
+ Union and ends of power
+ Brakes system
+ Support of the triangular form of interruption and direction
+ Body
+ Electric side equipment

Meeting of a head of cylinders

In spite of this, the chief went to a workshop to execute the service of valves, or not before beginning his meeting, carefully the component ones re-examine the purity of all.

After the return of a head of a workshop in him the valves with the component companions will be already installed. In this case it is necessary to lower proceedings of five next paragraphs and at the same time to pass to the actions described in the paragraph 7.

ORDER OF REALIZATION

1. First of all install in the captures of direction of valves of a saddle of his springs (companion sees an illustration).

It gives birth to a hat zastukivaniye straightly after this I eat completely it will "come" in the capture – the new punches can lead to the rubber damage. Follow that the trace of this the hats were not overinjured in captures.

2. Each one of the captures puts a new hat maslootrazhatelny of direction. The hats of Maslootrazhatelny (entry and final valves) "put themselves" in the guides of the capture for a careful zastukivaniye.

The hats of Maslootrazhatelny of entry and final valves disagree over a so great standard and are marked with a code to colors (companion sees an illustration) – they do not mix them.

3. Movement of an end of a head to other, polish with molibdensoderzhashchy or lubricant of reason of meeting to the first valve and post links in a head. Oil a nucleus of the valve pure reason.

4. Put a nucleus valvate springs and his plate (companion sees an illustration). The special instrument holds tight springs, having lowered a plate, soon it establishes in the flute opened in a few fine cookies of nucleus of valve of the lock that cuts.

The springs of Valvate are established by circles with the step come down to a head.

5. For aims of the temporary fixation of fine cookies to an otpuskaniye of the instrument they polish us of the interior with the dense lubricant (companion sees an illustration).

6. Repeat the proceeding for the remained valves. It looks what all the component ones settled down strictly at the ancient places.

7. Through a check of beat of calibre vernier the height of agreement of nucleuses of valves (distance of a spring saddle for a surface of face of a nucleus of the valve) (companion sees an illustration). If the repair of a head was done in a workshop of the service of the car, this parameter will be already adjusted properly. If the result some of measurements exceeds the value admissible in Specifications, it substitutes the corresponding valve and repeated check. If the substitution of the valve does not lead to the correction of a situation, therefore the saddle of the valve is installed when a head and the last thing exaggerated deeply they are subject to the substitution.

8. It wets with lubricant of reason of meeting surfaces of work of yokes of the walk of valves, cames and necks of the axle (axles) and an axle of yokes. Install in a head the axle (axles) and the meetings of the yokes (to see the Repair of Part of the motor without extraction of the car - the Civic model of the present Chapter).