Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Honda Tsivik
+ Cars of the mark of It Treats Full text and Honda Civic With care
+ Maintenance education
+ Regular maintenance
- Motor
   + Repair of the motor without extraction of the car - the Civic model
   + Repair of the motor without extraction of the car - the Full text model
   - General and repairs of capital of the motor
      General information
      Check of pressure of oil
      Check of pressure of compression in cylinders
      Diagnostic of a condition of the motor with use of the measure of vacuum
      Removal of the car of the unity of power - preparation and measured by precaution
      Removal and installation of the motor
      Alternative versions of schemes of repair of recuperation of the motor
      Order of desmontagem of the motor for preparation he to capital repairs
      Desmontagem of a head of cylinders
      To clean and check of a condition of a head of cylinders
      Valves service
      Meeting of a head of cylinders
      Removal of conrod and piston meetings
      Removal of an end of inclination
      Cleaning of the block of the motor
      Check of a condition of the block of the motor
      Honingovaniye of mirrors of cylinders
      Check of a condition of component ones of conrod and group of piston
      Check of a condition of an end of inclination
      Check of a state and selection of insertions of radical loads and conrod of an inclination end
      Order of meeting of motor
      Installation of rings of piston
      Installation of an end of inclination and check of slits of work of radical loads
      Substitution of a few back epiploon of an inclination end
      Installation of conrod and meetings of piston and check of size of slits of work in loads conrod of an inclination end
      Broken of proof and running in of the motor after capital repairs
+ Cooling of system and heating
+ System of provision of power and launch
+ Electric motor equipment
+ Systems of control of the motor
+ Box of dislocation of gear
+ Union and ends of power
+ Brakes system
+ Support of the triangular form of interruption and direction
+ Body
+ Electric side equipment

Honingovaniye of mirrors of cylinders

Before the meeting of the motor the honingovaniye of mirrors of cylinders for aims of the realization of the correct landing for them of rings of piston that supply the proper tension of cameras of combustion is executed without fail.

The absence of near to necessary instruments to the hand or repugnance of executing independently a honingovaniye, the work of the quite moderate payment can be accused to experts of a workshop of the service of the car.

Before beginning a honingovaniye, establish to the place of a covering of radical loads (without insertions) with his bridge and hold tight pins of fixation with the necessary effort.

Two types are given out of khans to prosecute of cylinders mirrors: хон like "the brush of bottle" and, хон more traditional, superficial in the form of a mouth with the sprung stones grinding. Both instruments supply the necessary quality of the processing of mirrors of cylinders though the use of the first one is more preferable for the inexperienced mechanic. Also enough rags, honingovochny special or only the liquid lubricating oil, and also the electric furadeira as the walk of mouths honingovochny will be needed.

Law in the next order:

ORDER OF REALIZATION

Do not forget of wide eyes or a front policeman put!

1. Insist хон on a cartridge of furadeira electrically, reduce the sprung grinding from stones / the sticks of the brush of a mouth and fill the last thing in the cylinder (companion sees an illustration).

2. Abundantly moisten a mirror of the cylinder prosecuted with the oil, include a furadeira and begin to do a mouth ahead and backwards movements in the cylinder. The speed of the vertical movement of a hon will supply the attraction of a surface of a mirror of the cylinder of a model setchatoobrazny with the angle of the crossroad of the parties of a cell approximately 60 ° (companion sees an illustration). Do not feel sorry for the oil and try not to withdraw any more material of a surface of walls of the cylinder, of which it is really necessary for the realization of the necessary result.

The manufacturers of rings of piston can impose demands themselves to the angle of the crossroad of the parties of a cell of a model of net – attentively they study the education on the packing of a remnabor.

3. Do not take хон from the cylinder to a stop full of a furadeira! Keep on doing ahead and backwards movements for a mouth until it does not stop revolving. After a stop of a furadeira they hold tight stones of grinding and take хон of the cylinder. When it uses the khan as "brush of bottle" hope for a stop full of a furadeira, soon it takes a mouth, keeping on making spinning manually a cartridge in the normal direction.
4. Rub with rags a mirror of the cylinder and it passes to a next honingovaniye.
5. After the realization of the processing, use an archive for the removal of facets of the superior edges of cylinders – this processing is done with the objective there were no difficulties with the petrol station in pistons cylinders with the rings that put themselves in them. Notice that the extreme care – does not scratch an archive a cylinder mirror.
6. In the conclusion the whole block has to wash itself carefully out for the hot solution of water of soap.

The cylinders can be considered washed out when after executing in a mirror the gray raid it does not remain the white rags moistened with the oil in him. Do not forget of all the oil openings clean a cylindrical brush and channels, soon the block washes out a water current below a pressure.

7. After washing itself carefully the perforated surfaces of the protection dry the block and oil they of the corrosion. Before the meeting of the motor they wrap up the block in a pure plastic bag.