Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Honda Tsivik
+ Cars of the mark of It Treats Full text and Honda Civic With care
+ Maintenance education
+ Regular maintenance
- Motor
   + Repair of the motor without extraction of the car - the Civic model
   + Repair of the motor without extraction of the car - the Full text model
   - General and repairs of capital of the motor
      General information
      Check of pressure of oil
      Check of pressure of compression in cylinders
      Diagnostic of a condition of the motor with use of the measure of vacuum
      Removal of the car of the unity of power - preparation and measured by precaution
      Removal and installation of the motor
      Alternative versions of schemes of repair of recuperation of the motor
      Order of desmontagem of the motor for preparation he to capital repairs
      Desmontagem of a head of cylinders
      To clean and check of a condition of a head of cylinders
      Valves service
      Meeting of a head of cylinders
      Removal of conrod and piston meetings
      Removal of an end of inclination
      Cleaning of the block of the motor
      Check of a condition of the block of the motor
      Honingovaniye of mirrors of cylinders
      Check of a condition of component ones of conrod and group of piston
      Check of a condition of an end of inclination
      Check of a state and selection of insertions of radical loads and conrod of an inclination end
      Order of meeting of motor
      Installation of rings of piston
      Installation of an end of inclination and check of slits of work of radical loads
      Substitution of a few back epiploon of an inclination end
      Installation of conrod and meetings of piston and check of size of slits of work in loads conrod of an inclination end
      Broken of proof and running in of the motor after capital repairs
+ Cooling of system and heating
+ System of provision of power and launch
+ Electric motor equipment
+ Systems of control of the motor
+ Box of dislocation of gear
+ Union and ends of power
+ Brakes system
+ Support of the triangular form of interruption and direction
+ Body
+ Electric side equipment

Removal of an end of inclination

The removal of an end of inclination is possible only of the motor been overcome with the car. It is destined that a pendulum / a driving disc, a cog-wheel of an end of inclination, a belt that distributes the gas, the trundle bed of case, a maslozabornik, the bomb of oil, a maslootrazhatel and (in motors B18B1) conrod and piston meetings are already demolished. Before the removal of an end of inclination also it is necessary for otboltit and when the bearer of a few back was separated of the cylinder block epiploon.

ORDER OF REALIZATION

1. Before the initial extraction of an end of inclination of the motor, measure the size of his play of axial side. Fix the DTI the coaxialmente measures of instrument in the block the end of inclination, when rested his diver against a face of one of cranks or a face of end of pin (companion seeing an illustration) the last thing.

The coverings of radical loads and his bridge of union will remain at the places, and his fixation corsets itself with the necessary effort.

2. Push an end of inclination against the stopped one behind and cancel indicative of device. Now push an end in an opposite direction and consider the indication of the instrument of measuring. The size of free one to go round of an end in the longitudinal direction also is his play of axial side. Compare the result of the measurement to Specifications demands. If the side play exceeds the very admissible value, check persistent surfaces of an end of the existence of signs of the excessive use. The absence of obvious signs of the use, the installation of new persistent lavadores normally helps to correct a situation.

3. The absence of near to to the hand the instrument of measuring of disc is possible to use the ordinary probe of the type of lezviyny. Exactly move an end against the stopped one ahead in the motor, soon determine the size of the slit formed between a face of a crank and an advanced wall of the radical load persistent (room), when there installed densely in him the corresponding thickness an edge (edges) of probe (companion seeing an illustration).

4th. Besides the number of series in the coverings marking in the form of the form firearms are supplied normally. In correctly established coverings of the firearm it will specify in the direction of a belt of GRM drive. In stages (in turns of 1/4 of the approximation) they weaken pins of the fixation of coverings of radical loads and / or his bridge of union so that the possibility of his reversion manually appeared.

4b. In the Civic models agreement marking they check coverings of radical loads of the existence in them. If need be put marking independently through a center punch.

4c. In Full text the models check coverings of radical loads of the existence in them agreement marking. The coverings have to be numbered constantly in the direction in the front behind in the motor (companion sees an illustration).

5. Discover radical loads or meeting of his bridge. In the Full text models exactly the hammer they explore the remained coverings with the gentle living creature for aims of his separation of the block of motor. In case of the necessity they use like levers that fix pins. Try not to leave insertions.
6. Carefully take an end of inclination of the motor (use the help of the spectator). Follow that the trace of this the insertions of radical loads remained in the beds in the block and coverings. Install coverings in the block, then to the hand hold tight pins of his fixation.