Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Honda Tsivik
+ Cars of the mark of It Treats Full text and Honda Civic With care
+ Maintenance education
+ Regular maintenance
- Motor
   + Repair of the motor without extraction of the car - the Civic model
   + Repair of the motor without extraction of the car - the Full text model
   - General and repairs of capital of the motor
      General information
      Check of pressure of oil
      Check of pressure of compression in cylinders
      Diagnostic of a condition of the motor with use of the measure of vacuum
      Removal of the car of the unity of power - preparation and measured by precaution
      Removal and installation of the motor
      Alternative versions of schemes of repair of recuperation of the motor
      Order of desmontagem of the motor for preparation he to capital repairs
      Desmontagem of a head of cylinders
      To clean and check of a condition of a head of cylinders
      Valves service
      Meeting of a head of cylinders
      Removal of conrod and piston meetings
      Removal of an end of inclination
      Cleaning of the block of the motor
      Check of a condition of the block of the motor
      Honingovaniye of mirrors of cylinders
      Check of a condition of component ones of conrod and group of piston
      Check of a condition of an end of inclination
      Check of a state and selection of insertions of radical loads and conrod of an inclination end
      Order of meeting of motor
      Installation of rings of piston
      Installation of an end of inclination and check of slits of work of radical loads
      Substitution of a few back epiploon of an inclination end
      Installation of conrod and meetings of piston and check of size of slits of work in loads conrod of an inclination end
      Broken of proof and running in of the motor after capital repairs
+ Cooling of system and heating
+ System of provision of power and launch
+ Electric motor equipment
+ Systems of control of the motor
+ Box of dislocation of gear
+ Union and ends of power
+ Brakes system
+ Support of the triangular form of interruption and direction
+ Body
+ Electric side equipment

Check of a condition of the block of the motor

ORDER OF REALIZATION

1. Previously the block has to be compensated carefully (to see the Cleaning of the block of the motor).
2. Do the extern inquiry of the block as for the identification of aspects of corrosion, slits and other damages. Check a condition of a woodcarving of very fast openings. Also it will be reasonable to do on trial of the block of the existence of the slits hidden in the conditions of a workshop of the service of the car with the use of the special diagnostic equipment. In case of the detection of defects the block is subject to repair of recuperation or substitution.
3. Check a condition of mirrors of cylinders.
4. The sizes of estimate that happen of conicity and ovality of cylinders (companions see illustrations).

5th. Diameter of measure of each one of cylinders in top (straightly below limit of use of step), the central and lower sections, in the beginning in the airplane of a parallel axle of an end of inclination (V), then – perpendicular to an axle of the block (A).

5b. The measurement of diameters of cylinders follows that it does through a telescopic nutromer and a micrometer. The capacity is correct to use a nutromer it comes not at the same time – they do not hurry, do several measurements until one secures of the conclusions fairness in absolute.

6. After the diameter is registered by a nutromer, measure the last thing with a micrometer (to see an illustration).

7. The size of conicity of the cylinder is determined by a difference between measurements results in the top and the lowest sections. Ovality calls the diameters difference in a parallel and perpendicular axle of an end of inclination the airplanes. Compare when they resulted from the check to admissible values (to see Specifications).
8. I work in the described way, in series check all the cylinders.
9. In the moment of the detection of perceptible defects or a detour of results of measurements of demands standard, the cylinder block is subject to the mechanical recuperation work in the conditions of a workshop of the service of the car. If in the course of the repair of boring recuperation of cylinders one did, the motor has to end with new pistons corresponding repair (with the excess) the size.

10th. Check planeness of the inter-connected surface of the block (companions see illustrations). Compare the result of measurements to Specifications demands, in case of the necessity they give the block to an in favor point.

10b. It executes the measurement in three directions: in an axle of the block and two of his diagonal ones.

11. If the condition of mirrors of cylinders during the realization of the check will be satisfactory in the simultaneous observance of demands standard to the form of cylinders and to slits of the landing piston in them (to see the Check of a condition of component ones of conrod and group of piston), the necessity of an in favor point of cylinders disappears. It will have only to carry out a honingovaniye of mirrors enough (to see Honingovaniye of mirrors of cylinders).

QX4.ONLINE
S40.ONLINE
A-8.ONLINE
W124.ONLINE
RX300.ONLINE
W140.ONLINE
B3-B4.SPACE
B3B4.SPACE
A-8.SPACE