Honda Civic/Acura Integra

from 1994 launch

Repair and operation of the car

Honda Tsivik
+ Cars of the mark of It Treats Full text and Honda Civic With care
+ Maintenance education
+ Regular maintenance
- Motor
   + Repair of the motor without extraction of the car - the Civic model
   + Repair of the motor without extraction of the car - the Full text model
   - General and repairs of capital of the motor
      General information
      Check of pressure of oil
      Check of pressure of compression in cylinders
      Diagnostic of a condition of the motor with use of the measure of vacuum
      Removal of the car of the unity of power - preparation and measured by precaution
      Removal and installation of the motor
      Alternative versions of schemes of repair of recuperation of the motor
      Order of desmontagem of the motor for preparation he to capital repairs
      Desmontagem of a head of cylinders
      To clean and check of a condition of a head of cylinders
      Valves service
      Meeting of a head of cylinders
      Removal of conrod and piston meetings
      Removal of an end of inclination
      Cleaning of the block of the motor
      Check of a condition of the block of the motor
      Honingovaniye of mirrors of cylinders
      Check of a condition of component ones of conrod and group of piston
      Check of a condition of an end of inclination
      Check of a state and selection of insertions of radical loads and conrod of an inclination end
      Order of meeting of motor
      Installation of rings of piston
      Installation of an end of inclination and check of slits of work of radical loads
      Substitution of a few back epiploon of an inclination end
      Installation of conrod and meetings of piston and check of size of slits of work in loads conrod of an inclination end
      Broken of proof and running in of the motor after capital repairs
+ Cooling of system and heating
+ System of provision of power and launch
+ Electric motor equipment
+ Systems of control of the motor
+ Box of dislocation of gear
+ Union and ends of power
+ Brakes system
+ Support of the triangular form of interruption and direction
+ Body
+ Electric side equipment

Check of a condition of an end of inclination

ORDER OF REALIZATION

1. Wash out a solvent of end of inclination, then carefully dry, having whenever possible worn-out compressed air.

When it uses compressed air do not forget of putting wide eyes!

2. Check radical necks and conrod of an end of inclination of the existence of zadir, cavities, slits and signs of the unequal use.

3. Withdraw with a stone of grinding, an archive or a scraper agnails of edges of openings of oil (companion sees an illustration).

4. Do not forget of cleaning a few rigid openings of oil of brush (companion to see an illustration). Then solvent washes them out.

5. Examine the whole surface of an end in the existence of slits and other damages. For the identification of the hidden slits it is necessary to resort to the magnetic powder defectoscopy – give an end to a workshop of the service of the car.

6. The measure for a few diameters of micrometer of radical necks and conrod of an end (companion sees an illustration). It executes the measurement of the diameter of each neck in several points in length and perimeter that there will allow to appreciate the size of his conicity and ovality that it must not exceed the limit of the admissible variety (to see Specifications). It is necessary also to appreciate the size of a thrashing of an end of inclination – the couple of blocks of V-shaped and the DTI to measure it of instrument is going to be needed – the absence of the necessary stock they ask the specialists of help of the service of the car.

7. In case of what wear/conicity/ovality of necks it exceeds the admissible size, or the mechanical surfaces damages happen, the inclination end must happen to an in favor point. After an in favor point of an end it is necessary to catch new insertions of radical loads and / or conrod of the size of corresponding repair.

8. Check a condition of necks omental in both pins of an end of inclination (companion sees an illustration). The existence of the flutes perforated for epiploons, agnails or zadir it will lead to an exit again epiploons out of the operation in near to the future. In certain cases fine captures can restore the pins for an in favor point and a napressovka in them. If such a recuperation repair is not possible, substitute an end.

9. Check a condition of insertions of radical loads and conrod (to see the Check of a state and the selection of insertions of radical loads and conrod of an inclination end).